Linksys WRT160N v2.0 is not supported. WRT160Nv3 Instructions. Read the Firmware FAQ and Peacock Announcement. Download eko build dd-wrt.v24-13575_NEWD-2_K2.6_mini_wrt160nv3.bin. NOTE: eko builds have disappeared, use the dd-wrt.v24-14929_NEWD-2_K2.6_mini_wrt160nv3.bin instead. Only use the trailed build (with "WRT160Nv3" in the file name)

Posted: Mon Oct 17, 2016 15:55 Post subject: What to do with a WRT160N V3 advice: So I have my two r6300v2 both and the WRT160N both on DD-WRT. WRT160N v3 is on wiki original flash. I have a ranch house and I have them strung out in the basement on the floor. My plans are to get everything locked in and run some wires upstairs. Forum discussion: I've been using a Linksys WRT160N for just over a year now. It has never worked as well as my old WRT54G, and lately it's been locking up every couple of days. It's become a real WRT160N-RM Details | Standards IEEE 802.3/3u, IEEE 802.11b/g, IEEE802.11n Draft Security WEP, WPA, WPA2 Security key bits: 128-bit, 256-bit WPA/WPA2 WPA2 WAN Ports 1 x 10/100M WAN; 4 x 10/100M LAN LEDs Ethernet (1-4), Wi-Fi Protected Setup, Wireless, Internet, Power Buttons Reset, Wi-Fi Protected Setup Antenna Internal Antenna Interface The Linksys WRT160N includes the following connection ports. Internet - Connects the router to the cable modem Ethernet (1-4) - Connects to the Ethernet port on your computer(s) Aug 28, 2011 · The WRT160N has Upnp but WHS does not seem to recognize or work with it so I resorted to seting-up my router manually, including forwarding ports 80, 443 and 4125 to my WHS's static IP address . Actually it was already set-up from the previous Home Server installation (accept for the currect static IP address), but it did not work with WHS 2011 Disabled DHCP on WRT160N, UPnP, and all firewall functions (the linux box handles that) Under "Basic Setup", I set the "Internet IP address" of the WRT160N to 192.168.9.1/24. Set its "Default Gateway" to 192.168.9.254/24. Connected a cat5 cable to one of the four wired ports on the back of the WRT160N to my third NIC. Configured WPA2-PSK on the

Disabled DHCP on WRT160N, UPnP, and all firewall functions (the linux box handles that) Under "Basic Setup", I set the "Internet IP address" of the WRT160N to 192.168.9.1/24. Set its "Default Gateway" to 192.168.9.254/24. Connected a cat5 cable to one of the four wired ports on the back of the WRT160N to my third NIC. Configured WPA2-PSK on the

WRT160N; Default settings of the Linksys WRT160N. Here you can find the default IP address and the password for the user interface of the Linksys WRT160N Wireless Broadband router. This site also contains information about the preconfigured Wi-Fi settings of the device.

Linksys WRT160N Remote Access Setup

There is 3 sets of pads on the PCB of the WRT160N. Half of the JP1 and JP3 pads are on the reverse side of the PCB. JP1 is the JTAG port. JP2 is a serial port and it works if you use a 3.3v TTL to RS-232. * There is a hidden EXTERNAL serial port above the YELLOW INTERNET sticker inside the RJ-45 jack. Nov 06, 2009 · Learning to reset the Linksys WRT160N wireless-N router is important if you currently change the settings within the administrative pages. The reason it is important is because one wrong setting change could make it difficult to access the Internet or the administrative pages of of the router.